钛合金螺旋铣孔的切削力和切削温度试验研究

螺旋铣孔技术是航空装备制造领域新出现的制孔技术,因具有加工质量好、效率高等优点被用于加工钛合金、复合材料等难加工材料.采用包括切削速度、切向每齿进给量、轴向每齿进给量和螺旋导程4个基本加工参数描述螺旋铣孔过程,分析了基本参数和螺旋铣孔输入加工参数(自转、公转、进给)之间的关系.在自行研制的螺旋铣孔试验平台上开展了钛合金材料的加工试验,研究了钛合金螺旋铣孔加工中切削温度及切削力的特征,以及基本加工参数对切削温度和切削力的影响规律.试验结果表明,在螺旋导程一定时,切削温度主要由切削速度决定,而与轴向每齿进给量及切向每齿进给量无明显关系;而切削力的影响规律与切削温度相反.切削温度是影响螺旋铣孔过程中刀具磨损及加工孔质量的主要因素.在需同时保证加工效率及加工质量的前提下,应尽量选择大的切向每齿进给量、大的轴向每齿进给量和较低的切削速度.     

Prediction of cutting forces in ball-end milling of 2.5D C/C composites

Machining of carbon/carbon (C/C) composite materials is difficult to carry out due to its high specific stiffness, brittleness, anisotropic, non-homogeneous and low thermal conductivity, which can result in tear, burr, poor surface quality and rapid wear of cutters. Accurate and fast pre-diction of cutting forces is important for milling C/C composite materials with high quality. This paper presents an alternative cutting force model involving the influences of the directions of fiber. Based on the calculated and experimental results, the cutting forces’ coefficients of 2.5D C/C com-posites are evaluated using multiple linear regression method. Verification experiment has been car-ried out through a group of orthogonal tests. Results indicate that the proposed model is reliable and can be used to predict the cutting forces in ball-end milling of 2.5D C/C composites.     

基于响应曲面法的高速内冷铣削AISI304不锈钢铣削力

针对硬质合金刀具高速内冷铣削AISI304不锈钢时,切削力大、切削温度高及加工表面质量低的问题。基于响应曲面中心复合设计方法进行高速内冷铣削实验,建立了铣削力分量二阶回归预测模型,并进行了实验验证。对比了干式与内冷铣削后的加工表面质量,分析了铣削参数对铣削力分量的影响规律,以铣削力分量最小为目标优化了铣削参数。结果表明:进给力和径向力的预测值与实验值的误差分别为4. 77%和6. 16%;内冷铣削的Ra为0. 193～0. 327μm;对铣削力分量的影响是铣削深度转速进给量,随着铣削深度和转速的增加,进给力先升高后降低,径向力逐步增加,铣削深度与转速的交互作用对进给力和径向力的影响显著;转速11 643. 63 r/min、铣削深度1 mm、进给量0. 08 mm/r为最优铣削参数组合。     

C/SiC复合材料螺旋铣削与钻削制孔效果对比

采用PCD刀具对C/SiC复合材料螺旋铣削与钻削制孔的制孔效果进行了对比研究。在同等加工效率条件下测量了两种制孔方法产生的切削力及切削热,并观察制孔质量。试验结果表明:螺旋铣孔产生的轴向力小于钻孔,约为钻孔的56.9%;孔壁粗糙度及孔径差均小于钻削;钻孔产生的切削热少于螺旋铣削制孔,约占螺旋铣的58.7%,但螺旋铣产生的切削热对材料及刀具的影响小。     

大直径螺纹数控加工工艺研究与应用

针对形状结构复杂的某产品上34个M36×3-6H内螺纹加工进行了工艺攻关,提出采用旋风铣的方法,并编制数控加工程序,有效解决了难加工材料大直径内螺纹的加工难题,在此基础上实现了数控加工程序的参数化,理论上可以实现任意直径、任意螺距、任意深度螺纹的加工,并在其他型号产品上得到应用。     

多重纳米结构轻质高强铝基复合材料的制备和组织性能

为了研究多重纳米结构对块体材料强化和变形能力的影响机制,采用粉末冶金法制备了多重纳米结构的B4C颗粒增强铝基复合材料,并对复合材料的强化和形变破坏机制进行了定量和定性的讨论。由100%球磨复合粉末制备的块体复合材料的室温压缩强度为670MPa;当加入10vol%气雾化态的Al2024粉末后,复合材料的室温压缩强度升高到1.115GPa;之后随着气雾化态Al2024粉末含量的增加,复合材料的强度逐渐下降,但是没有产生明显的塑性变形;当气雾化态Al2024粉末的含量增加到50vol%时,复合材料的压缩强度下降到580MPa,断裂前变形率达到了10%。扫描电镜(SEM)和透射电镜(TEM)的分析结果显示,亚微米级的B4C颗粒、位错以及纳米晶基体分别通过Orowan强化、位错强化和细晶强化机制对复合材料进行强化;粗晶Al2024区域与复合结构区域的比例显著影响复合材料的形变及破坏机制。     

不同介质下高速铣削钛合金时切屑的变形研究

开展了不同介质下钛合金切屑变形的高速铣削试验研究,分析比较了不同介质、不同铣削速度对切屑宏观和微观形貌的影响及其原因,得出了干铣削、空气油雾和氮气油雾介质下切屑变形的各自特点以及切屑变形随速度而变化的规律。     

复合铣整体叶盘通道加工工艺规划分析

首先对开式整体叶盘通道几何特征进行分析,在宽度和深度上对通道加工空间进行计算,从轴向和径向进行切削加工性分析;通过偏置面求解及其延伸面求解,进而确定可加工区域;在对比分析各种铣削方法基础上,优选复合铣削数控刀具,明确通道复合铣加工方法以及流程,为后续开式整体叶盘通道加工工艺优化打下基础。     

基于宏程序的外球面粗精加工

目前,小内存的数控机床仍然是我国机床的主流,使加工程序变得简洁,对实际加工有着很重要的意义.宏程序的应用可以大大简化编程,本文通过实例介绍了数控铣削加工外球面的宏程序.     

Stability analysis of robotic longitudinal-torsional composite ultrasonic milling

Currently, industrial robots are considered as an alternative towards traditional machine tools. Especially for the large-scale parts milling, robotic flexibility and low cost make it possess the irreplaceability. However, the milling chatter caused by its weak rigidity hampers robotic application and promotion severely in aviation industry. Rotary ultrasonic milling (RUM) technology with one-dimensional axial vibration has been proven and approved on avoiding robotic chatter. Based on this, the research of project team demonstrates that longitudinal-torsional composite ultrasonic milling (CUM-LT) involving separation characteristic has a greater advantage than RUM in terms of chatter suppression. Thereby, the CUM-LT as a new means is applied to avoid processing vibration of robotic milling system. And its influence mechanism on stability improvement of weak stiffness processing system is clarified. Meanwhile, the approaches to strengthen separation effect are provided innovatively. Moreover, a new analysis method of robotic CUM-LT (RCUM-LT) stability is proposed on the basis of ultrasonic function angles. The simulation and experimental results indicate that compared with robotic RUM (RRUM), stability regions of separated RCUM-LT (SRCUM-LT) and unseparated RCUM-LT (URCUM-LT) are improved by 124.42% and 39.20%, respectively. The addition of torsional ultrasonic energy has a wonderful effect on the milling chatter suppression of low stiffness robots.